P .O. Box 245040Milwaukee, WI 53224-9540P hone: 414.354.0300F ax: 414.354.7905www.u-line.comPrinted in U.S.A. P/N 30-10009Échelon™USERMANUAL
CONNECTING A DRAIN PUMPIf a gravity drain connection is not available, and you have not pur-chased the CLR2060 with factory installed pump, we strongl
ELECTROCUTION HAZARD!Electrical Grounding Required. This applianceis equipped with a three prong (grounding)polarized plug for your protection against
NOTE Stainless Steel models require a minimum of 2-1/2" doorclearance.6. Install and connect the water supply line. See CONNECTING THEWATER SUPP
11CONNECTING THE WATER SUPPLY1. Remove grille from front ofthe unit (see Figure 4). Referto CONDENSER CLEANING.2. Remove the back panel toease water
4. Locate the compression fit-ting and ferrule packed in theunit. Slide the compressionfitting and ferrule over the1/4 inch water supply line.Do not
NOTE After completing the installation, turn on the water andrecheck water and drain connection for leaks. Apply addi-tional tightening if needed. Do
14User’s Manual3. Check the levelness after each adjustment and repeat the previoussteps until the unit is level.REVERSING THE DOORAll U-Line units (
151. Remove top hinge screw pin(7/64" Allen wrench) fromcabinet (see Figure 13).Remove door by tilting forwardand lifting off bottom hinge pin.F
5. Remove existing bottom hinge (3 screws) and remount on opposite side TOP. Remove hinge screw pin.6. With bottom of door facing up, remove pivot pla
CUSTOM DOOR PANELSTwo types of custom door panels can be installed on your U-Line unitto harmonize with or accent the surrounding decor.FULL OVERLAY D
U-LINE CORPORATION LIMITED WARRANTYU-Line Corporation warrants each U-Line product to be free from defects in materials andworkmanship for a period of
Install the insert as follows:Insert edges may beSHARP! Use care wheninstalling.1. Remove top hinge screw pin (7/64" Allen wrench, see Figure20)
BUILT-IN INSTALLATIONYour U-Line product has been designed for either free-standing or built-in installation. When built-in, your U-Line product does
INITIAL START-UPOnce installation and leveling is complete, the unit is ready for initialstart-up and operation. Your unit is shipped in the OFF posit
NORMAL OPERATIONThe ice maker is designed to make clear ice from most water sourceson a consistent basis. Water is constantly circulated over the evap
MAINTENANCEPeriodic cleaning and proper maintenance will ensure efficiency, top performance, and long life. The maintenance intervals listed are based
• DO NOT use solvent cleaning agents or abrasives on theinterior. These cleansers may transmit taste to the icecubes, or damage or discolor the interi
DO NOT touch the condenser fins. The condenser fins areSHARP and can be easily damaged.DO NOT use any type of cleaner on the condenser unit.3. Clean t
Ice machine cleaner is used to remove lime scale and other mineraldeposits. Refer to the following steps for mineral deposit removal.Never use anythin
9. When the self-cleaning process stops (approximately 45 minutes)it may be desirable to clean the storage bin at this time (see INTERIOR CLEANING).10
STORAGE, VACATION AND MOVINGIf the unit is to be stored, moved or not used for extended periods, itwill be necessary to drain the system of water.Elec
INTRODUCTIONCongratulations on your purchase of a U-Line CLR2060 Ice Maker. Apioneer in the field for nearly 40 years, U-Line is the world’s numberone
28User’s Manual7. Reconnect inlet and outlet lines to the water valve.8. Replace front access panel.9. Replace grille.10. Drain water from the w
29TROUBLESHOOTINGBEFORE CALLING FOR SERVICEIf the unit appears to be malfunctioning, read through NORMAL OPER-ATION first. If the problem persists, ch
Problem Possible Cause RemedyUnit runs but Scale and mineral Clean unit. See produces very buildup in unit. MAINTENANCE.little ice.Inadequate airflo
31Problem Possible Cause RemedyWater leaking Supply line leaking. Check to see that water from under the inlet line is attached to unit. inlet valve
Notes_________________________________________________________________________________________________________________________________________________
U-LINE CORPORATION LIMITED WARRANTYU-Line Corporation warrants each U-Line product to be free from defects in materials andworkmanship for a period of
P .O. Box 245040Milwaukee, WI 53224-9540P hone: 414.354.0300F ax: 414.354.7905www.u-line.comPrinted in U.S.A. P/N 30-10009Échelon™USERMANUAL
If you do not return your Warranty Registration Card, U-Line will usethe date of sale to the U-Line distributor as the first date of warrantyfor your
3SAFETY PRECAUTIONSDo not attempt to install or operate your unit until you have read thesafety precautions in this manual. Safety items throughout th
4User’s ManualGENERAL PRECAUTIONSRISK OF CHILD ENTRAPMENT. Before you throw away yourold refrigerator or freezer, take off the doors and leaveshelves
5INSTALLATION DIMENSIONSFigure 1DRAIN INSTALLATIONPLEASE READ all instructions completely before attemptingto install or operate the unit. All Ice Mak
6User’s ManualFollow these guidelines when installing drain lines to prevent water fromflowing back into the ice maker storage bin and/or potentially
3.Remove 12 screws and back panel.4. Check that the clamps and hose connections are tight at the fol-lowing areas:• Discharge tube (A)• Drain tube (
Kommentare zu diesen Handbüchern