U-line CO29 Bedienungsanleitung PDF herunterladen (Seite 14)

U-Line Electrical / Plumbing Specfications 12

CAUTION

Plumbing installation must observe all state and local

codes. All water and drain connections MUST BE made by

a licensed/qualified plumbing contractor. Failure to follow

recommendations and instructions may result in damage

and/or harm.

Water Supply Connection

When connecting the water supply, follow these guidelines:

• Review the local plumbing codes before you install the unit.

• Connect to the cold water supply.

• The water pressure should be between 20 and 120 psi.

• The water line MUST have a shut-off valve in the 1/4” O.D.

supply line.

• Leave approximately 8’ of water line to be coiled behind the

appliance. The water line should be looped into 2 coils. This

will allow the unit to be removed for cleaning and servicing.

However, make certain that the tubing is not pinched or

damaged during installation.

IMPORTANTIMPORTANT

U-Line requires the use of copper tubing for installation.

Do not use any plastic water supply line. The line is under

pressure at all times. Plastic may crack or rupture with

age and cause water damage to your home.

To connect to water supply:

1. Locate the desired cold

water supply location. Attach

a 1/4” copper line to this

location and route the tubing

to the appliance. Leave

approximately 8’ of water line

to be coiled behind the

appliance. The water line

should be looped into 2 coils.

This will allow the line to flex

when removing the unit for

cleaning and servicing.

2. Locate the U-Line supplied

garden hose fitting. Ensure the

end of the copper tubing has

been cut straight and free of

burrs. Slide the compression

nut and ferrule onto the

copper tubing as shown. Push

the assembly completely into

the garden hose fitting and

tighten using the two

wrenches.

Drain Connection (CLR2160 CLRCO2175)

IMPORTANTIMPORTANT

• Drain can NOT be located directly below unit. Unit has

a solid base that will not allow the unit to drain below

itself.

• We strongly recommend the use of a U-Line drain kit

for both gravity & pump installations. A complete drain

kit containing all the items needed to connect your unit

are available from your dealer. Part No. U-

CLRDRAINKIT.

• Longer drain connections may require additional drain

hose lengths. Additional drain line can be purchased

from your dealer or directly from McMaster-Carr.

(McMaster-Carr # 52375K35)

The CLR2160 or CLRCO2175 can be installed using a Gravity

Drain, a Factory-Installed Drain Pump (U-Line P60) or a Locally-

Installed (U-Line P60) Drain Pump. Drain lines must have a 5/8”

inside diameter. The floor drain must be large enough to

accommodate drainage from all attached drains.

Follow these guidelines when installing drain lines to prevent water

from flowing back into the ice maker storage bin and/or potentially

flowing onto the floor, causing water damage:

Gravity Drain

A Gravity Drain may be used if:

• Drain line has at least a 1-inch drop per 48 inches of run (1/4

inch per foot).

• Drain line does not create traps

or created traps are vented.

If using a Gravity Drain:

1. Slide 2 hose clamps onto the

drain connection on the rear of

the appliance.

2. Insert the barbed fitting halfway

into this connection.

3. On the other end of this barbed

fitting attach the 5/8” braided

tubing.

4. Slide a clamp on each side of the

barbed fitting as shown (see

Figure 39).

5. Insulate the drain line, if necessary to prevent condensation.

11 Prepare Plumbing

9/16" Wrench

1/4" Copper Water

Supply Line

7/16" Wrench

From Water Supply

to Ice Maker

Normal

Proper Drain

With Trap

Poor Drainage, Water Will Back Up

With Trap and Vent

Proper Drain

Drain Fitting from

Back of Unit

Worm Clamps

Drain Line

5/8" x 5/8"

Barb Connector

ULIN_S_0166b2_A

1 2 ... 9 10 11 12 13 14 15 16 17 18 19

Kommentare zu diesen Handbüchern

Keine Kommentare

U-line CO29 Bedienungsanleitung Seite 14

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kühlschränke U-line CO29